Tasmota: Opening Closing as a percentage of time

[matteo2019]

I thank all those who answer me in advance. I have a dual R2 sonoff with stefanbode tasmota firmware. My problem is to open / close the shutter at a certain time with a certain percentage.
Example: I set the 7 o'clock timer and the shutter is raised with the seconds established by the shutteropenduration function, I open it 100%. At 8 o'clock I want to get the blind down by 20% of the total opening, always setting the timer.
I await your answers, please explain in detail.

[meingraham]

Support for Stefan's firmware fork should be directed to his GitHub.

Please close this issue.

[matteo2019]

how can I refer you to your GitHub?

[ascillato2]

Please, address this to the Tasmota Support Chat. The chat is a better and more dynamic channel for helping you. Github issues are meant for Tasmota Software Bug Reporting.

Please check the Contributing Guideline and Policy and the Support Guide.

Thanks.

---

Support Information

See Wiki for more information.
See FAQ for common questions/answers and links if none of your question is in the list
See Chat for more user experience.
See Community for forum.
See Code of Conduct

[localhost61]

@matteo2019
Michael was talking about stefan's fork
For your usage you'll have to enable and use Rules together with Clock#Timer triggers.
Current Stefanbode fork is almost up to date with Tasmota, so you can use Tasmota wiki for your information.

[matteo2019]

localhost61. I need some examples to understand it well. Could you help me?

[matteo2019]

examples of rules to apply

[localhost61]

These are some of the commands I enter in the console to rule my rollershutters which are

• currently using Tasmota (not a fork)
• wired with Relay 1=Down, Relay2=Up
• all wired with wall switches on GPIO0 & GPIO9 ( ⚠ DualR2 won't boot after power outage if GPIO0=Gnd)
• opening with sunrise but one after the other with a 2" delay to avoid current rush if all of them were launched together.
• at 100% open they wait 200ms and roll back during 200ms to release the pressure.

This is for 4th rollershutter, delay is sun+6":

poweronstate 0          // Keep relay(s) off after power on
ledstatus 1         // LED open when a relay is ON
setoption0 off          // PowerOn relays state is Off
setoption14 on          // Relay interlock
setoption26 on          // Postfix on Power msg 
switchmode1 2           // Relay follow inverted wall switch state (ON when pin grounded)
switchmode2 2           // Relay follow inverted wall switch state (ON when pin grounded)
pulsetime1 120          // Power1 will be released after 20s
pulsetime2 120          // Power2 will be released after 20s
timezone 99         // Enable Sunset/Sunrise computation
backlog latitude 48.11; longitude -1.68     // geolocation for sun elevation computation
Timer1 {"Arm":1,"Mode":2,"Window":0,"Days":"1111111","Repeat":1,"Output":1,"Action":3}  // Mode2=Sunset
Timer2 {"Arm":1,"Mode":1,"Window":0,"Days":"1111111","Repeat":1,"Output":2,"Action":3}  // Mode1=Sunrise
rule1 on Clock#Timer=1 do backlog delay 60; power1 1 endon On Clock#Timer=2 do backlog delay 60; power2 1;delay 220;power2 0;delay 2;power1 1;delay 2;power1 0 endon // Define both  rules launched at sunset & sunrise
rule on             // Enable rules

It doesn't fit your need but can be of little help. Good luck

[Jason2866]

@matteo2019 You know what a wiki is?
It is absolute no go to change or add something in wiki which is a personal question!!!
https://github.com/arendst/Sonoff-Tasmota/wiki/Opening---Closing-as-a-percentage-of-time/8c6ac8c8f38dab29849e4da66ae92e205e39b5b4
Page will be reverted.
Take this as a warning. Disregard of the rules one more time and you will be locked out from here.

Please read and respect Contributing Guideline and Policy and the Support Guide.

Support Information

See Wiki for more information.
See Chat for more user experience.
See Community for forum.
See Code of Conduct

[matteo2019]

@Jason2866 do not get upset. I don't know how to move to ask for information. I have to learn where I can ask for advice and information hoping to be helped. I'm sorry you turned to threats.

[matteo2019]

@Jason2866 if I have made some false steps, forgive me. I was not motivated by arrogance and indifference.

[localhost61]

@matteo2019 Tasmota is a collaborative work and you are destroying it. It should be read only but in order to enable everybody to give help you are allowed to add information. I personally don't consider @Jason2866 warning as offending, he is preserving the collaborative job and I think everybody involved here would thank him for that.

[matteo2019]

Quite right! I apologize it was not my intention to ruin his work. I would like to return to the chat where meingraham invited me

[Jason2866]

Most Wiki updates the last months are from @blakadder and @meingraham
I try to support ;-)

[matteo2019]

Thanks for the support. I would like to participate in the chat. Why do I get written that I was banned?

Ottieni Outlook per Androidhttps://aka.ms/ghei36

---

From: Adrian Scillato [e-mail]
Sent: Tuesday, June 11, 2019 11:03:59 PM
To: arendst/Sonoff-Tasmota
Cc: matteo2019; Author
Subject: Re: [arendst/Sonoff-Tasmota] Opening Closing as a percentage of time (#5946)

Please, address this to the Tasmota Support Chathttps://discord.gg/Ks2Kzd4. The chat is a better and more dynamic channel for helping you. Github issues are meant for Tasmota Software Bug Reporting.

Please check the Contributing Guideline and Policyhttps://github.com/arendst/Sonoff-Tasmota/blob/development/CONTRIBUTING.md and the Support Guidehttps://github.com/arendst/Sonoff-Tasmota/blob/development/SUPPORT.md.

Thanks.

---

Support Information

See Wikihttps://github.com/arendst/Sonoff-Tasmota/wiki for more information.
See FAQhttps://github.com/arendst/Sonoff-Tasmota/wiki/FAQ for common questions/answers and linkshttps://github.com/arendst/Sonoff-Tasmota/wiki/FAQ#i-cannot-find-an-answer-here if none of your question is in the list
See Chathttps://discord.gg/Ks2Kzd4 for more user experience.
See Communityhttps://groups.google.com/d/forum/sonoffusers for forum.
See Code of Conducthttps://github.com/arendst/Sonoff-Tasmota/blob/development/CODE_OF_CONDUCT.md

—
You are receiving this because you authored the thread.
Reply to this email directly, view it on GitHubhttps://github.com/arendst/Sonoff-Tasmota/issues/5946?email_source=notifications&email_token=AMIAS34GEJPODMRTSTUPVIDP2AHL7A5CNFSM4HXCUD52YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGODXOP2UI#issuecomment-501022033, or mute the threadhttps://github.com/notifications/unsubscribe-auth/AMIAS354ZKDMQ3QGE2CTVDDP2AHL7ANCNFSM4HXCUD5Q.