Operating-system: Raspberry Pi 4-image

[pepeEL]

Hi
Now is released Raspberry Pi 4 :)
When we can think that image for Raspberry Pi 4 will be available ?

[homeassistantmi2]

Can yo release immediately hassos on Rpi4 ?
Only option now is use manual installation on linux
ResinOS it also not work on rpi4

[Joeboyc2]

Just wait a little bit, give the devs a chance!

On Sat, 29 Jun 2019, 20:36 homeassistantmi2, [e-mail]
wrote:

Can yo release immediately hassos on Rpi4 ?
Only option now is use manual installation on linux
ResinOS it also not work on rpi4

—
You are receiving this because you are subscribed to this thread.
Reply to this email directly, view it on GitHub
https://github.com/home-assistant/hassos/issues/413?email_source=notifications&email_token=AB6SOLT23YQTLP2ACXQYJXDP462TDA5CNFSM4H24MOE2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGODY363XQ#issuecomment-506981854,
or mute the thread
https://github.com/notifications/unsubscribe-auth/AB6SOLRTW5QKNYWU3N46DPTP462TDANCNFSM4H24MOEQ
.

[pepeEL]

And good will be add support boot from ssd on usb3. 0
This is very need.

[pvizeli]

We can first add support for RPi4 if u-boot (our bootloader they we use because we are a embedded system) have a support patch.

[skynet01]

Would be amazing if we can just take out our sd card from Rpi3 and stick it in Rpi4 and it just starts working like nothing happend 🥰

[Joeboyc2]

I think that's an impossibility due to the changes thr new hardware has.

Nothing wrong with starting again 😁

On Wed, 3 Jul 2019, 10:55 skynet01, [e-mail] wrote:

Would be amazing if we can just take out our sd card from Rpi3 and stick
it in Rpi4 and it just starts working like nothing happend 🥰

—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
https://github.com/home-assistant/hassos/issues/413?email_source=notifications&email_token=AB6SOLRDFI7SW577RDQKPX3P5RZR5A5CNFSM4H24MOE2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGODZD55ZY#issuecomment-508026599,
or mute the thread
https://github.com/notifications/unsubscribe-auth/AB6SOLVFLF6REOBMEGMCGLDP5RZR5ANCNFSM4H24MOEQ
.

[pvizeli]

@Joeboyc2 have right, there are complete different bootloader and microcode to setup the CPU and start the kernel. Raspbian work a bit different, they can handle that because they but everthing into same image and support only 32bit.

[pvizeli]

Support start with 3.3

[skynet01]

Woohoo! Thank you!

[Joeboyc2]

I'll be flashing it tonight, will let you know of I have any issues 😁

On Tue, 16 Jul 2019, 18:30 skynet01, [e-mail] wrote:

Woohoo! Thank you!

—
You are receiving this because you were mentioned.
Reply to this email directly, view it on GitHub
https://github.com/home-assistant/hassos/issues/413?email_source=notifications&email_token=AB6SOLSW35TK6KJ7PEVYU63P7YAUTA5CNFSM4H24MOE2YY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOD2BSQMA#issuecomment-511911984,
or mute the thread
https://github.com/notifications/unsubscribe-auth/AB6SOLXQIGZ3LQCI7DVXWYLP7YAUTANCNFSM4H24MOEQ
.

[Joeboyc2]

oh.... @pvizeli i dont see the pi 4 image.... which one should i use to flash ? the pi3 one?

[MrYadro]

You just have to wait a bit while they are building, now they are up in assets

[skynet01]

So stoked to try it. Is there going to be a migration tutorial of some sort from Pi3+? Or you just flash it and restore a snapshot?

[Joeboyc2]

Ah i see them now, literally only 22 assets when i check and sent the message, 24 now :)