Zigbee2mqtt: Can't pair Ikea Tradfri LED1623G12
Although it is a supported device and I know it works for some people, I'm not able to pair any of these devices. I tried the master as well as the dev branch (commit #98302be) and I've reflashed the z-stack firmware. Xiaomi Mija temp sensors and buttons paired without issues.
Factory resetting the bulbs did not solve the problem.
Any hints?
gabe0815
All 10 comments
Do you keep it close (a few cms) to the coordinator after factory reset?
Koenkk
on 15 Oct 2018
I've placed the bulb < 5cm from the zigbee-sniffer (CC2531) and I've removed all other Tradfri bulbs from any sockets after I reflashed and reinstalled the zigbee-stack and zigbee2mqtt.
gabe0815
on 15 Oct 2018
Can you move the sniffer and bulb to a different location to make sure it doesn't connect to another zigbee network?
Koenkk
on 15 Oct 2018
Set the bridge to pairing off and pairing on again. I wrote a little Windows Forms Tool to act as a Mqtt-Client. But and other Mqtt-Client will also do that trick.
bmachuletz
on 15 Oct 2018
I setup iobroker with iobroker.zigbee adapter (0.7.5) and I'm still not able to pair any of my 3 Tradfri bulbs. My Xiaomi temp sensor (WSDCGQ01LM) pairs on first try... Is there anyway to troubleshoot this further?
gabe0815
on 15 Oct 2018
My temp sensors are pairing with no Problems too. To pair the TRÃ…DFRI bulb set pairing of via mqtt and set pairing on again. This should do the thing.
On Mon, Oct 15, 2018 at 9:05 PM +0200, "gabe0815" notifications@github.com wrote:
I setup iobroker with iobroker.zigbee adapter (0.7.5) and I'm still not able to pair any of my 3 Tradfri bulbs. My Xiaomi temp sensor (WSDCGQ01LM) pairs on first try... Is there anyway to troubleshoot this further?
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub, or mute the thread.
bmachuletz
on 15 Oct 2018
I switched zigbee2mqtt/bridge/config/permit_join from true/false several times (resetting the bulbs) without success.
gabe0815
on 15 Oct 2018
Do you have the IKEA Gateway powered in. Please       try pairing with IKEA Gateway switched off.
On Mon, Oct 15, 2018 at 9:26 PM +0200, "gabe0815" notifications@github.com wrote:
I switched zigbee2mqtt/bridge/config/permit_join from true/false several times (resetting the bulbs) without success.
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub, or mute the thread.
bmachuletz
on 15 Oct 2018
I do not own a Tradfri gateway. The only other zigbee devices I have are Xiaomi sensors and switches (no gateway neither).
gabe0815
on 15 Oct 2018
I finally managed to pair the Ikea Tradfri LED1623G12. It turns out, I was never able to perform a factory reset. Carlessly flicking on and off the bulb never worked for me.
To properly reset the bulbs, the off-time must be longer (~2 s) than the on time (<1 s). The distance to the coordinator is not super critical (1.5 m in my case) and other devices (Tradfri and Xiaomi) can be on and paired at the same time.
Thanks for your help and this great project!
gabe0815
on 18 Oct 2018
Related issues
pepp86
·
4Comments
alwashe
·
4Comments
tb-killa
·
3Comments
jwilling
·
4Comments
ophilips
·
4Comments
Most helpful comment
I finally managed to pair the Ikea Tradfri LED1623G12. It turns out, I was never able to perform a factory reset. Carlessly flicking on and off the bulb never worked for me.
To properly reset the bulbs, the off-time must be longer (~2 s) than the on time (<1 s). The distance to the coordinator is not super critical (1.5 m in my case) and other devices (Tradfri and Xiaomi) can be on and paired at the same time.
Thanks for your help and this great project!