Dear Marlin users and developers, we the Marlin Development team, require your assistance filling the following Google Form: http://goo.gl/forms/gRsLbQmti6
It's a "one minute" survey were we ask you which board and Marlin version you use.
You may submit multiple times for more than one printer.
jbrazio
All 20 comments
maybe add what IDE they use?
boelle
on 10 May 2016
I have posted it on the G+ Rigidbot forum.
Regards,
Ernesto
On 10 May 2016, at 22:47, João Brázio [email protected] wrote:
Dear Marlin users and developers, we the Marlin Development team, require your assistance filling the following Google Form: http://goo.gl/forms/gRsLbQmti6
It's a "one minute" survey were we ask you which board and Marlin version you use.
You may submit multiple times for more than one printer.—
You are receiving this because you are subscribed to this thread.
Reply to this email directly or view it on GitHub
emartinez167
on 10 May 2016
@boelle good suggestion, added.
jbrazio
on 10 May 2016
Joao,
Some Rigidbot users are not quite sure what to respond regarding the version of Firmware they are on, as it is the original supplied by Rigidbot (we suspect it is an old fork from 1.0). Is there a way for them to provide that information (or add an option stating Rigidbot original FW)?
Regards,
Ernesto
On 10 May 2016, at 22:47, João Brázio [email protected] wrote:
Dear Marlin users and developers, we the Marlin Development team, require your assistance filling the following Google Form: http://goo.gl/forms/gRsLbQmti6
It's a "one minute" survey were we ask you which board and Marlin version you use.
You may submit multiple times for more than one printer.—
You are receiving this because you are subscribed to this thread.
Reply to this email directly or view it on GitHub
emartinez167
on 11 May 2016
@emartinez167 I added the option "Other/Builtin" and "Other/Unknown".
Interesting to see those people have never upgraded their firmware, is it for any particular reason ?
jbrazio
on 11 May 2016
Where can we see the results?
Blue-Marlin
on 11 May 2016
I believe mostly because of one or more of the following reasons:
a) Code in that version tied to the hardware for that machine
b) a lot of users unfamiliar/uncomfortable with coding Arduino
c) If it ain't broken, don't fix it attitude
d) Lack of knowledge about the existence of a mainstream Marlin
e) Originally the Rigidbot was not officially supported by mainstream Marlin. I submitted the original PR and @thinkyhead completed it for me. It was a long time between the RB coming to the market and the PR. Ini the interim, some RB users with enough knowledge rigged up what is known in the community as RBC (RigidbotCommunity) version which was based on a newer version, but it stayed there and never caught up with the current release.
Regards,
Ernesto
On 11 May 2016, at 07:59, João Brázio [email protected] wrote:
@emartinez167 I added the option "Other/Builtin" and "Other/Unknown".
Interesting to see those people have never upgraded their firmware, is it for any particular reason ?—
You are receiving this because you were mentioned.
Reply to this email directly or view it on GitHub
emartinez167
on 11 May 2016
Two problems, my board not listed, no way to select a custom board (4 power outs: EEFB) (I chose ramps 1.4 as a default) No way to allow for not using an unmodified Marlin firmware. ( I chose the RD branch that I am currently working from, eg RC 6) I got the IDE question OK :)
RalphSutherland
on 11 May 2016
But it's a RAMPS 1.4 or does it have any pin diff ?
I listed all boards on boards.h, there was the only way to have some consistency.
jbrazio
on 11 May 2016
Shouldn't it be 1.1.0-RCx instead of 1.1.1-RCx?
tkurbad
on 11 May 2016
Damn you're right :-/
jbrazio
on 11 May 2016
BOARD_MKS_13 is missing from the list...
JimBrown
on 12 May 2016
It should also note that the "MKS" is the same as the "HICTOP" for those who have that branding.
thinkyhead
on 12 May 2016
Where can we see the results?
boelle
on 12 May 2016
I will post them soon, just waiting for the survey to ran at least one week.
@Roxy-3DPrintBoard could you please share the link in the forums you have access to ?
We are having a bit less than 200 data points right now.
jbrazio
on 12 May 2016
are there any results yet?
maybe just view access to the data
boelle
on 24 May 2016
Will do !
jbrazio
on 24 May 2016
@JBrazio I just saw the request to post it in different forums. (I need
your email address!!!)
It is posted at both RepRap.org (in the Marlin section) and at
3D-PrintBoard in the RepRap section.
On Tue, May 24, 2016 at 10:15 AM, João Brázio [email protected]
wrote:
Will do !
—
You are receiving this because you were mentioned.
Reply to this email directly or view it on GitHub
https://github.com/MarlinFirmware/Marlin/issues/3726#issuecomment-221304078
Roxy-3D
on 24 May 2016
@Roxy-3DPrintBoard I will post it on the chat we have.
jbrazio
on 24 May 2016
Published in spanish google group (Clone Wars)
VicentM
on 24 May 2016
Related issues
Anion-anion
·
3Comments
StefanBruens
·
4Comments
Tamonir
·
3Comments
Kaibob2
·
4Comments
ahsnuet09
·
3Comments
Most helpful comment
Published in spanish google group (Clone Wars)