Addons: deCONZ - FATAL: No device since 3.4 / 3.5

[mcfrojd]

Today i updated deCONZ addon first to 3.4 and then to 3.5
On both new versions i get this error when i try to start the addon.

[16:52:47] FATAL: No device /dev/serial/by-id/usb-dresden_elektronik_ingenieurtechnik_GmbH_ConBee_II_DE1962254-if00 found!
That device path shows under "hassio/system/hardware" and worked on addon version 3.3

I have tried to change the device to this diffrent ones (one by one) but they give same error.
"/dev/ttyUSB0"
"/dev/ttyUSB1"
"/dev/ttyAMA0"
"/dev/ttyAMA1"
"/dev/ttyACM0"
"/dev/ttyACM1"

Restoring from snapshot to 3.3 makes it work again

[KennethLavrsen]

Hi. I have the same issue. But you can make it work with /dev/ttyACM#. But you have to restart Home Assistant. It is not enough to restart the addon.

This is really annoying. I was so happy when the addon was changed so it accept the by-id links as my Aeotec and Conbee randomly swap between 0 and 1 when I reboot the host machine.

We need that restored again. It is important that you can use these /dev/serial/by-id/blabla links so things are predictable and reliable.

[KennethLavrsen]

@pvizeli it seems you did the change that broke the use of /dev/serial/by-id links. We had been begging for this feature and finally got it a month or so ago. It would be really good if you would fix your latest changes so it works again. You cannot rely on direct /dev/tty links and you all the normal udev tricks do not work as they also create symlinks that don't work.

When I look at the changes it seems the purpose was to make by-id links work in Centos.

Well - the changes broke that functionality in Ubuntu it seems. I run hass.io on Ubuntu 18.04

[pvizeli]

Can't see any issue with Supervisor 185 and docker 18.09 or 19.03

[mattias1972]

My deCONZ addon also broke when updating from 3.3 to 3.5, refuses to start.
Log entrys:
2019-09-03 21:31:23 ERROR (MainThread) [.] Error connecting to deCONZ gateway at 172.30.32.1
2019-09-03 21:31:23 WARNING (MainThread) [homeassistant.config_entries] Config entry for deconz not ready yet. Retrying in 5 seconds.

[pvizeli]

what say the dmesg after start?

[mattias1972]

This is the complete dmesg from last boot, there are an awful lot of entrys about the conbee…
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.14.98-v7 (root@ff157cc86da3) (gcc version 7.3.0 (Buildroot 2018.11.1-g39a27fe4)) #1 SMP Sat May 11 02:17:06 UTC 2019
[ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c5383d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] OF: fdt: Machine model: Raspberry Pi 3 Model B Plus Rev 1.3
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] cma: Reserved 8 MiB at 0x3ac00000
[ 0.000000] On node 0 totalpages: 242688
[ 0.000000] free_area_init_node: node 0, pgdat 80d8dd40, node_mem_map ba39f000
[ 0.000000] Normal zone: 2133 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 242688 pages, LIFO batch:31
[ 0.000000] percpu: Embedded 17 pages/cpu @ba347000 s39564 r8192 d21876 u69632
[ 0.000000] pcpu-alloc: s39564 r8192 d21876 u69632 alloc=17*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 240555
[ 0.000000] Kernel command line: zram.enabled=1 zram.num_devices=3 apparmor=1 security=apparmor rootwait cgroup_enable=memory 8250.nr_uarts=0 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2708_fb.fbswap=1 vc_mem.mem_base=0x3ec00000 vc_mem.mem_size=0x40000000 dwc_otg.lpm_enable=0 console=tty1 root=PARTUUID=8d3d53e3-6d49-4c38-8349-aff6859e82fd rootfstype=squashfs ro rauc.slot=A
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 939152K/970752K available (8192K kernel code, 612K rwdata, 2268K rodata, 1024K init, 710K bss, 23408K reserved, 8192K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xbb800000 - 0xff800000 (1088 MB)
[ 0.000000] lowmem : 0x80000000 - 0xbb400000 ( 948 MB)
[ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB)
[ 0.000000] .text : 0x80008000 - 0x80900000 (9184 kB)
[ 0.000000] .init : 0x80c00000 - 0x80d00000 (1024 kB)
[ 0.000000] .data : 0x80d00000 - 0x80d992ac ( 613 kB)
[ 0.000000] .bss : 0x80da148c - 0x80e52ef0 ( 711 kB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] ftrace: allocating 28767 entries in 85 pages
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] arch_timer: cp15 timer(s) running at 19.20MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000007] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000021] Switching to timer-based delay loop, resolution 52ns
[ 0.000284] Console: colour dummy device 80x30
[ 0.000840] console [tty1] enabled
[ 0.000877] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[ 0.000917] pid_max: default: 32768 minimum: 301
[ 0.001069] Security Framework initialized
[ 0.001152] AppArmor: AppArmor initialized
[ 0.001353] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.001386] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.002266] CPU: Testing write buffer coherency: ok
[ 0.002703] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.003122] Setting up static identity map for 0x100000 - 0x10003c
[ 0.003264] Hierarchical SRCU implementation.
[ 0.003956] smp: Bringing up secondary CPUs ...
[ 0.004732] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.005534] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.006306] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.006411] smp: Brought up 1 node, 4 CPUs
[ 0.006485] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[ 0.006507] CPU: All CPU(s) started in HYP mode.
[ 0.006525] CPU: Virtualization extensions available.
[ 0.007498] devtmpfs: initialized
[ 0.017734] random: get_random_u32 called from bucket_table_alloc+0x120/0x24c with crng_init=0
[ 0.018572] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4
[ 0.018806] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.018849] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.019526] pinctrl core: initialized pinctrl subsystem
[ 0.020308] NET: Registered protocol family 16
[ 0.023054] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[ 0.027893] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[ 0.027925] hw-breakpoint: maximum watchpoint size is 8 bytes.
[ 0.028129] Serial: AMBA PL011 UART driver
[ 0.029856] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[ 0.030359] uart-pl011 3f201000.serial: could not find pctldev for node /soc/gpio@7e200000/uart0_pins, deferring probe
[ 0.061909] bcm2835-dma 3f007000.dma: DMA legacy API manager at bb813000, dmachans=0x1
[ 0.063368] SCSI subsystem initialized
[ 0.063603] usbcore: registered new interface driver usbfs
[ 0.063673] usbcore: registered new interface driver hub
[ 0.063772] usbcore: registered new device driver usb
[ 0.070070] raspberrypi-firmware soc:firmware: Attached to firmware from 2019-02-12 19:42
[ 0.071553] clocksource: Switched to clocksource arch_sys_counter
[ 0.154964] VFS: Disk quotas dquot_6.6.0
[ 0.155087] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.155275] FS-Cache: Loaded
[ 0.155496] CacheFiles: Loaded
[ 0.155900] AppArmor: AppArmor Filesystem Enabled
[ 0.164816] NET: Registered protocol family 2
[ 0.165549] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.165677] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.165879] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.166027] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.166089] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.166405] NET: Registered protocol family 1
[ 0.166887] RPC: Registered named UNIX socket transport module.
[ 0.166911] RPC: Registered udp transport module.
[ 0.166930] RPC: Registered tcp transport module.
[ 0.166950] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.168297] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available
[ 0.170308] audit: initializing netlink subsys (disabled)
[ 0.170504] audit: type=2000 audit(0.159:1): state=initialized audit_enabled=0 res=1
[ 0.171147] workingset: timestamp_bits=14 max_order=18 bucket_order=4
[ 0.178925] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.179206] FS-Cache: Netfs 'nfs' registered for caching
[ 0.179827] NFS: Registering the id_resolver key type
[ 0.179885] Key type id_resolver registered
[ 0.179905] Key type id_legacy registered
[ 0.179934] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.182523] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.182695] io scheduler noop registered
[ 0.182717] io scheduler deadline registered
[ 0.182900] io scheduler cfq registered (default)
[ 0.182923] io scheduler mq-deadline registered
[ 0.182942] io scheduler kyber registered
[ 0.185300] BCM2708FB: allocated DMA memory fad00000
[ 0.185344] BCM2708FB: allocated DMA channel 0 @ bb813000
[ 0.190247] Console: switching to colour frame buffer device 82x26
[ 0.198344] bcm2835-rng 3f104000.rng: hwrng registered
[ 0.200852] vc-mem: phys_addr:0x00000000 mem_base=0x3ec00000 mem_size:0x40000000(1024 MiB)
[ 0.206345] vc-sm: Videocore shared memory driver
[ 0.209140] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[ 0.223599] brd: module loaded
[ 0.234697] loop: module loaded
[ 0.237628] zram: Added device: zram0
[ 0.240430] zram: Added device: zram1
[ 0.243188] zram: Added device: zram2
[ 0.245328] Loading iSCSI transport class v2.0-870.
[ 0.248115] libphy: Fixed MDIO Bus: probed
[ 0.250287] tun: Universal TUN/TAP device driver, 1.6
[ 0.252763] usbcore: registered new interface driver lan78xx
[ 0.255017] usbcore: registered new interface driver smsc95xx
[ 0.257129] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[ 0.259439] dwc_otg 3f980000.usb: base=0xf0980000
[ 0.461704] Core Release: 2.80a
[ 0.463768] Setting default values for core params
[ 0.465895] Finished setting default values for core params
[ 0.668287] Using Buffer DMA mode
[ 0.670454] Periodic Transfer Interrupt Enhancement - disabled
[ 0.672702] Multiprocessor Interrupt Enhancement - disabled
[ 0.674986] OTG VER PARAM: 0, OTG VER FLAG: 0
[ 0.677233] Dedicated Tx FIFOs mode
[ 0.679814] WARN::dwc_otg_hcd_init:1046: FIQ DMA bounce buffers: virt = 0xbad14000 dma = 0xfad14000 len=9024
[ 0.684272] FIQ FSM acceleration enabled for :
[ 0.684272] Non-periodic Split Transactions
[ 0.684272] Periodic Split Transactions
[ 0.684272] High-Speed Isochronous Endpoints
[ 0.684272] Interrupt/Control Split Transaction hack enabled
[ 0.694771] dwc_otg: Microframe scheduler enabled
[ 0.694820] WARN::hcd_init_fiq:459: FIQ on core 1 at 0x8065cb70
[ 0.697000] WARN::hcd_init_fiq:460: FIQ ASM at 0x8065cecc length 36
[ 0.699231] WARN::hcd_init_fiq:486: MPHI regs_base at 0xf0006000
[ 0.701564] dwc_otg 3f980000.usb: DWC OTG Controller
[ 0.703868] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[ 0.706229] dwc_otg 3f980000.usb: irq 62, io mem 0x00000000
[ 0.708574] Init: Port Power? op_state=1
[ 0.710840] Init: Power Port (0)
[ 0.713325] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.715704] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.718086] usb usb1: Product: DWC OTG Controller
[ 0.720442] usb usb1: Manufacturer: Linux 4.14.98-v7 dwc_otg_hcd
[ 0.722852] usb usb1: SerialNumber: 3f980000.usb
[ 0.725752] hub 1-0:1.0: USB hub found
[ 0.728098] hub 1-0:1.0: 1 port detected
[ 0.730840] dwc_otg: FIQ enabled
[ 0.730845] dwc_otg: NAK holdoff enabled
[ 0.730850] dwc_otg: FIQ split-transaction FSM enabled
[ 0.730860] Module dwc_common_port init
[ 0.731106] usbcore: registered new interface driver usb-storage
[ 0.733548] usbcore: registered new interface driver usbserial
[ 0.735813] usbcore: registered new interface driver usbserial_generic
[ 0.738045] usbserial: USB Serial support registered for generic
[ 0.740384] mousedev: PS/2 mouse device common for all mice
[ 0.742596] IR NEC protocol handler initialized
[ 0.744705] IR RC5(x/sz) protocol handler initialized
[ 0.746838] IR RC6 protocol handler initialized
[ 0.748976] IR JVC protocol handler initialized
[ 0.751074] IR Sony protocol handler initialized
[ 0.753172] IR SANYO protocol handler initialized
[ 0.755229] IR Sharp protocol handler initialized
[ 0.757244] IR MCE Keyboard/mouse protocol handler initialized
[ 0.759301] IR XMP protocol handler initialized
[ 0.762027] bcm2835-wdt 3f100000.watchdog: Broadcom BCM2835 watchdog timer
[ 0.764392] bcm2835-cpufreq: min=600000 max=1400000
[ 0.766848] sdhci: Secure Digital Host Controller Interface driver
[ 0.768962] sdhci: Copyright(c) Pierre Ossman
[ 0.771428] mmc-bcm2835 3f300000.mmc: could not get clk, deferring probe
[ 0.773645] sdhost-bcm2835 3f202000.mmc: could not get clk, deferring probe
[ 0.774643] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.776631] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.777656] hidraw: raw HID events driver (C) Jiri Kosina
[ 0.778701] usbcore: registered new interface driver usbhid
[ 0.779676] usbhid: USB HID core driver
[ 0.780958] vchiq: vchiq_init_state: slot_zero = bad80000, is_master = 0
[ 0.791304] nf_conntrack version 0.5.0 (15360 buckets, 61440 max)
[ 0.792572] IPVS: Registered protocols (TCP, UDP, SCTP, AH, ESP)
[ 0.793635] IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
[ 0.794971] IPVS: ipvs loaded.
[ 0.796018] IPVS: [rr] scheduler registered.
[ 0.797246] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 0.798814] NET: Registered protocol family 10
[ 0.800362] Segment Routing with IPv6
[ 0.801478] NET: Registered protocol family 17
[ 0.802635] Bridge firewalling registered
[ 0.803771] Key type dns_resolver registered
[ 0.805113] Registering SWP/SWPB emulation handler
[ 0.806499] registered taskstats version 1
[ 0.807591] AppArmor: AppArmor sha1 policy hashing enabled
[ 0.811528] uart-pl011 3f201000.serial: cts_event_workaround enabled
[ 0.812683] 3f201000.serial: ttyAMA0 at MMIO 0x3f201000 (irq = 87, base_baud = 0) is a PL011 rev2
[ 0.815670] mmc-bcm2835 3f300000.mmc: mmc_debug:0 mmc_debug2:0
[ 0.816759] mmc-bcm2835 3f300000.mmc: DMA channel allocated
[ 0.872172] sdhost: log_buf @ bad13000 (fad13000)
[ 0.909692] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 0.912249] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 0.914769] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 0.918429] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 0.941650] Indeed it is in host mode hprt0 = 00021501
[ 1.003938] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[ 1.007263] console [netcon0] enabled
[ 1.008675] netconsole: network logging started
[ 1.009605] of_cfs_init
[ 1.010551] of_cfs_init: OK
[ 1.011745] Waiting for root device PARTUUID=8d3d53e3-6d49-4c38-8349-aff6859e82fd...
[ 1.015037] random: fast init done
[ 1.063827] mmc1: new high speed SDIO card at address 0001
[ 1.141556] mmc0: host does not support reading read-only switch, assuming write-enable
[ 1.149979] mmc0: new high speed SDHC card at address aaaa
[ 1.152380] usb 1-1: new high-speed USB device number 2 using dwc_otg
[ 1.154926] Indeed it is in host mode hprt0 = 00001101
[ 1.217865] mmcblk0: mmc0:aaaa SC32G 29.7 GiB
[ 1.229713] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8
[ 1.256304] VFS: Mounted root (squashfs filesystem) readonly on device 179:3.
[ 1.260583] devtmpfs: mounted
[ 1.267901] Freeing unused kernel memory: 1024K
[ 1.391946] usb 1-1: New USB device found, idVendor=0424, idProduct=2514
[ 1.394507] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.397633] hub 1-1:1.0: USB hub found
[ 1.400328] hub 1-1:1.0: 4 ports detected
[ 1.572802] random: systemd: uninitialized urandom read (16 bytes read)
[ 1.721600] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[ 1.858412] random: systemd: uninitialized urandom read (16 bytes read)
[ 1.861803] usb 1-1.1: New USB device found, idVendor=0424, idProduct=2514
[ 1.861808] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.862134] hub 1-1.1:1.0: USB hub found
[ 1.862180] hub 1-1.1:1.0: 3 ports detected
[ 1.867388] random: systemd: uninitialized urandom read (16 bytes read)
[ 1.961628] usb 1-1.2: new full-speed USB device number 4 using dwc_otg
[ 2.117049] usb 1-1.2: New USB device found, idVendor=0403, idProduct=6001
[ 2.118153] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.119240] usb 1-1.2: Product: RFXtrx433
[ 2.120429] usb 1-1.2: Manufacturer: RFXCOM
[ 2.121647] usb 1-1.2: SerialNumber: 07WBSV41
[ 2.144180] zram2: detected capacity change from 0 to 16777216
[ 2.144208] zram1: detected capacity change from 0 to 33554432
[ 2.144252] zram0: detected capacity change from 0 to 194228224
[ 2.191656] usb 1-1.1.2: new full-speed USB device number 5 using dwc_otg
[ 2.300881] usbcore: registered new interface driver ftdi_sio
[ 2.302922] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 2.304275] ftdi_sio 1-1.2:1.0: FTDI USB Serial Device converter detected
[ 2.305919] usb 1-1.2: Detected FT232RL
[ 2.308941] usb 1-1.2: FTDI USB Serial Device converter now attached to ttyUSB0
[ 2.326072] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2.327247] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.329396] usb 1-1.1.2: Product: ConBee II
[ 2.330445] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2.331520] usb 1-1.1.2: SerialNumber: DE1996448
[ 2.421627] usb 1-1.3: new full-speed USB device number 6 using dwc_otg
[ 2.434408] snd_bcm2835: module is from the staging directory, the quality is unknown, you have been warned.
[ 2.438567] bcm2835_alsa bcm2835_alsa: card created with 8 channels
[ 2.554944] usb 1-1.3: New USB device found, idVendor=0658, idProduct=0200
[ 2.556151] usb 1-1.3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.606239] brcmfmac: F1 signature read @0x18000000=0x15264345
[ 2.610097] brcmfmac: brcmf_fw_map_chip_to_name: using brcm/brcmfmac43455-sdio.bin for chip 0x004345(17221) rev 0x000006
[ 2.613926] usbcore: registered new interface driver brcmfmac
[ 2.651626] usb 1-1.1.1: new high-speed USB device number 7 using dwc_otg
[ 2.687535] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2.689911] cdc_acm 1-1.3:1.0: ttyACM1: USB ACM device
[ 2.691894] usbcore: registered new interface driver cdc_acm
[ 2.693158] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.781850] usb 1-1.1.1: New USB device found, idVendor=0424, idProduct=7800
[ 2.783130] usb 1-1.1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.849314] random: crng init done
[ 2.850558] random: 7 urandom warning(s) missed due to ratelimiting
[ 2.870993] brcmfmac: brcmf_c_preinit_dcmds: Firmware version = wl0: Feb 27 2018 03:15:32 version 7.45.154 (r684107 CY) FWID 01-4fbe0b04
[ 2.879703] brcmfmac: brcmf_c_preinit_dcmds: CLM version = API: 12.2 Data: 9.10.105 Compiler: 1.29.4 ClmImport: 1.36.3 Creation: 2018-03-09 18:56:28
[ 2.890514] EXT4-fs (mmcblk0p7): mounted filesystem with ordered data mode. Opts: (null)
[ 3.045625] EXT4-fs (zram1): mounted filesystem without journal. Opts: nobarrier
[ 3.051152] libphy: lan78xx-mdiobus: probed
[ 3.055081] Adding 189672k swap on /dev/zram0. Priority:-2 extents:1 across:189672k SSFS
[ 3.061534] lan78xx 1-1.1.1:1.0 (unnamed net_device) (uninitialized): int urb period 64
[ 3.147897] EXT4-fs (zram2): mounted filesystem without journal. Opts: nobarrier
[ 3.164720] EXT4-fs (mmcblk0p8): mounted filesystem with ordered data mode. Opts: (null)
[ 3.511643] usb 1-1.1.3: new low-speed USB device number 8 using dwc_otg
[ 3.691119] usb 1-1.1.3: New USB device found, idVendor=051d, idProduct=0002
[ 3.693757] usb 1-1.1.3: New USB device strings: Mfr=3, Product=1, SerialNumber=2
[ 3.698765] usb 1-1.1.3: Product: Back-UPS ES 700G FW:871.O4 .I USB FW:O4
[ 3.701357] usb 1-1.1.3: Manufacturer: APC
[ 3.703896] usb 1-1.1.3: SerialNumber: 5B1836T05783
[ 3.918884] hid-generic 0003:051D:0002.0001: hiddev96,hidraw0: USB HID v1.10 Device [APC Back-UPS ES 700G FW:871.O4 .I USB FW:O4 ] on usb-3f980000.usb-1.1.3/input0
[ 4.574503] uart-pl011 3f201000.serial: no DMA platform data
[ 4.838020] audit: type=1400 audit(1567538977.839:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="hassio-supervisor" pid=251 comm="apparmor_parser"
[ 4.842355] audit: type=1400 audit(1567538977.839:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="hassio-supervisor///usr/bin/gdbus" pid=251 comm="apparmor_parser"
[ 4.849793] audit: type=1400 audit(1567538977.839:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="hassio-supervisor///usr/bin/git" pid=251 comm="apparmor_parser"
[ 4.858050] audit: type=1400 audit(1567538977.839:2): apparmor="STATUS" operation="profile_load" profile="unconfined" name="hassio-supervisor///usr/bin/socat" pid=251 comm="apparmor_parser"
[ 4.864252] audit: type=1300 audit(1567538977.839:2): arch=40000028 syscall=4 per=800000 success=yes exit=70460 a0=6 a1=76d5b008 a2=1133c a3=0 items=0 ppid=250 pid=251 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="apparmor_parser" exe="/usr/sbin/apparmor_parser" key=(null)
[ 4.864266] audit: type=1327 audit(1567538977.839:2): proctitle=61707061726D6F725F706172736572002D72002D57002D4C002F6D6E742F646174612F73757065727669736F722F61707061726D6F722F6361636865002F6D6E742F646174612F73757065727669736F722F61707061726D6F722F68617373696F2D73757065727669736F72
[ 5.239392] Bluetooth: Core ver 2.22
[ 5.243449] NET: Registered protocol family 31
[ 5.247566] Bluetooth: HCI device and connection manager initialized
[ 5.249477] Bluetooth: HCI socket layer initialized
[ 5.250973] Bluetooth: L2CAP socket layer initialized
[ 5.252520] Bluetooth: SCO socket layer initialized
[ 5.270839] Bluetooth: HCI UART driver ver 2.3
[ 5.272672] Bluetooth: HCI UART protocol H4 registered
[ 5.274300] Bluetooth: HCI UART protocol Three-wire (H5) registered
[ 5.275816] Bluetooth: HCI UART protocol Broadcom registered
[ 5.391972] usb 1-1.1.2: USB disconnect, device number 5
[ 5.489701] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 5.492473] Bluetooth: BNEP filters: protocol multicast
[ 5.495243] Bluetooth: BNEP socket layer initialized
[ 5.711643] usb 1-1.1.2: new full-speed USB device number 9 using dwc_otg
[ 5.845936] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 5.848152] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5.852345] usb 1-1.1.2: Product: ConBee II
[ 5.854479] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 5.856699] usb 1-1.1.2: SerialNumber: DE1996448
[ 5.862279] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 6.461293] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.465410] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6.473352] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6.490686] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6.516044] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6.517073] brcmfmac: power management disabled
[ 7.035185] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 7.037531] brcmfmac: power management disabled
[ 7.224945] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 12.603394] audit: type=1400 audit(1567538985.609:3): apparmor="STATUS" operation="profile_load" profile="unconfined" name="docker-default" pid=337 comm="apparmor_parser"
[ 12.606551] audit: type=1300 audit(1567538985.609:3): arch=40000028 syscall=4 per=800000 success=yes exit=7945 a0=4 a1=195d778 a2=1f09 a3=0 items=0 ppid=336 pid=337 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="apparmor_parser" exe="/usr/sbin/apparmor_parser" key=(null)
[ 12.612258] audit: type=1327 audit(1567538985.609:3): proctitle=61707061726D6F725F706172736572002D4B72002F6D6E742F646174612F646F636B65722F746D702F646F636B65722D64656661756C74313633383231393036
[ 14.150533] audit: type=1325 audit(1567538987.149:4): table=nat family=2 entries=5
[ 14.153293] audit: type=1300 audit(1567538987.149:4): arch=40000028 syscall=294 per=800000 success=yes exit=0 a0=4 a1=0 a2=40 a3=955848 items=0 ppid=306 pid=362 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="iptables" exe="/usr/sbin/xtables-multi" key=(null)
[ 14.158861] audit: type=1327 audit(1567538987.149:4): proctitle=2F7573722F7362696E2F69707461626C6573002D2D77616974002D74006E6174002D4E00444F434B4552
[ 14.171395] audit: type=1325 audit(1567538987.169:5): table=filter family=2 entries=4
[ 14.174664] audit: type=1300 audit(1567538987.169:5): arch=40000028 syscall=294 per=800000 success=yes exit=0 a0=4 a1=0 a2=40 a3=fdc738 items=0 ppid=306 pid=364 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="iptables" exe="/usr/sbin/xtables-multi" key=(null)
[ 14.181346] audit: type=1327 audit(1567538987.169:5): proctitle=2F7573722F7362696E2F69707461626C6573002D2D77616974002D740066696C746572002D4E00444F434B4552
[ 14.185398] audit: type=1325 audit(1567538987.189:6): table=filter family=2 entries=6
[ 14.264261] Initializing XFRM netlink socket
[ 14.303884] Netfilter messages via NETLINK v0.30.
[ 14.314658] ctnetlink v0.93: registering with nfnetlink.
[ 14.886580] IPv6: ADDRCONF(NETDEV_UP): hassio: link is not ready
[ 15.085703] IPv6: ADDRCONF(NETDEV_UP): docker0: link is not ready
[ 19.337964] docker0: port 1(veth571965b) entered blocking state
[ 19.339256] docker0: port 1(veth571965b) entered disabled state
[ 19.340843] device veth571965b entered promiscuous mode
[ 19.342352] kauditd_printk_skb: 140 callbacks suppressed
[ 19.342356] audit: type=1700 audit(1567538992.339:53): dev=veth571965b prom=256 old_prom=0 auid=4294967295 uid=0 gid=0 ses=4294967295
[ 19.343025] IPv6: ADDRCONF(NETDEV_UP): veth571965b: link is not ready
[ 19.343642] audit: type=1300 audit(1567538992.339:53): arch=40000028 syscall=290 per=800000 success=yes exit=40 a0=c a1=3bb15f0 a2=28 a3=0 items=0 ppid=1 pid=306 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="dockerd" exe="/usr/bin/dockerd" key=(null)
[ 19.352152] audit: type=1327 audit(1567538992.339:53): proctitle=2F7573722F62696E2F646F636B657264002D480066643A2F2F002D2D73746F726167652D6472697665723D6F7665726C617932002D2D6C6F672D6472697665723D6A6F75726E616C64002D2D646174612D726F6F74002F6D6E742F646174612F646F636B6572
[ 19.399861] hassio: port 1(vethc5bb2b7) entered blocking state
[ 19.401345] hassio: port 1(vethc5bb2b7) entered disabled state
[ 19.403229] device vethc5bb2b7 entered promiscuous mode
[ 19.404600] audit: type=1700 audit(1567538992.399:54): dev=vethc5bb2b7 prom=256 old_prom=0 auid=4294967295 uid=0 gid=0 ses=4294967295
[ 19.405170] IPv6: ADDRCONF(NETDEV_UP): vethc5bb2b7: link is not ready
[ 19.407251] audit: type=1300 audit(1567538992.399:54): arch=40000028 syscall=290 per=800000 success=yes exit=40 a0=c a1=3ddc2d0 a2=28 a3=0 items=0 ppid=1 pid=306 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="dockerd" exe="/usr/bin/dockerd" key=(null)
[ 19.408590] hassio: port 1(vethc5bb2b7) entered blocking state
[ 19.414196] audit: type=1327 audit(1567538992.399:54): proctitle=2F7573722F62696E2F646F636B657264002D480066643A2F2F002D2D73746F726167652D6472697665723D6F7665726C617932002D2D6C6F672D6472697665723D6A6F75726E616C64002D2D646174612D726F6F74002F6D6E742F646174612F646F636B6572
[ 19.415610] hassio: port 1(vethc5bb2b7) entered forwarding state
[ 19.422983] hassio: port 1(vethc5bb2b7) entered disabled state
[ 20.434808] eth0: renamed from vetha8c2f83
[ 20.473207] IPv6: ADDRCONF(NETDEV_CHANGE): veth571965b: link becomes ready
[ 20.476684] docker0: port 1(veth571965b) entered blocking state
[ 20.479907] docker0: port 1(veth571965b) entered forwarding state
[ 20.483409] IPv6: ADDRCONF(NETDEV_CHANGE): docker0: link becomes ready
[ 20.647855] audit: type=1325 audit(1567538993.649:55): table=filter family=2 entries=0
[ 20.811742] audit: type=1300 audit(1567538993.649:55): arch=40000028 syscall=295 per=800000 success=yes exit=0 a0=4 a1=0 a2=40 a3=7ef07a94 items=0 ppid=618 pid=629 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="iptables" exe="/usr/sbin/xtables-multi" key=(null)
[ 20.825342] audit: type=1327 audit(1567538993.649:55): proctitle=2F7573722F7362696E2F69707461626C6573002D2D77616974002D4C002D6E
[ 20.832732] audit: type=1325 audit(1567538993.839:56): table=nat family=2 entries=0
[ 21.463202] eth1: renamed from veth1a0fcfc
[ 21.503886] IPv6: ADDRCONF(NETDEV_CHANGE): vethc5bb2b7: link becomes ready
[ 21.507386] hassio: port 1(vethc5bb2b7) entered blocking state
[ 21.510623] hassio: port 1(vethc5bb2b7) entered forwarding state
[ 21.514181] IPv6: ADDRCONF(NETDEV_CHANGE): hassio: link becomes ready
[ 27.838900] kauditd_printk_skb: 26 callbacks suppressed
[ 27.838906] audit: type=1400 audit(1567539000.839:65): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="hassio-supervisor" pid=734 comm="apparmor_parser"
[ 27.844570] audit: type=1400 audit(1567539000.839:65): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="hassio-supervisor///usr/bin/gdbus" pid=734 comm="apparmor_parser"
[ 27.849311] audit: type=1400 audit(1567539000.839:65): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="hassio-supervisor///usr/bin/git" pid=734 comm="apparmor_parser"
[ 27.853950] audit: type=1400 audit(1567539000.839:65): apparmor="STATUS" operation="profile_replace" info="same as current profile, skipping" profile="unconfined" name="hassio-supervisor///usr/bin/socat" pid=734 comm="apparmor_parser"
[ 27.858406] audit: type=1300 audit(1567539000.839:65): arch=40000028 syscall=4 per=800000 success=yes exit=70460 a0=6 a1=76d3a008 a2=1133c a3=0 items=0 ppid=733 pid=734 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="apparmor_parser" exe="/usr/sbin/apparmor_parser" key=(null)
[ 27.865689] audit: type=1327 audit(1567539000.839:65): proctitle=61707061726D6F725F706172736572002D72002D57002D4C002F6D6E742F646174612F73757065727669736F722F61707061726D6F722F6361636865002F6D6E742F646174612F73757065727669736F722F61707061726D6F722F68617373696F2D73757065727669736F72
[ 28.488742] hassio: port 2(vethc59b871) entered blocking state
[ 28.490316] hassio: port 2(vethc59b871) entered disabled state
[ 28.497791] device vethc59b871 entered promiscuous mode
[ 28.499466] audit: type=1700 audit(1567539001.489:66): dev=vethc59b871 prom=256 old_prom=0 auid=4294967295 uid=0 gid=0 ses=4294967295
[ 28.502813] audit: type=1300 audit(1567539001.489:66): arch=40000028 syscall=290 per=800000 success=yes exit=40 a0=c a1=4359c20 a2=28 a3=0 items=0 ppid=1 pid=306 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="dockerd" exe="/usr/bin/dockerd" key=(null)
[ 28.503530] IPv6: ADDRCONF(NETDEV_UP): vethc59b871: link is not ready
[ 28.508953] audit: type=1327 audit(1567539001.489:66): proctitle=2F7573722F62696E2F646F636B657264002D480066643A2F2F002D2D73746F726167652D6472697665723D6F7665726C617932002D2D6C6F672D6472697665723D6A6F75726E616C64002D2D646174612D726F6F74002F6D6E742F646174612F646F636B6572
[ 29.429783] audit: type=1325 audit(1567539002.429:67): table=filter family=2 entries=0
[ 30.334071] eth0: renamed from vethbe77bb9
[ 30.393073] IPv6: ADDRCONF(NETDEV_CHANGE): vethc59b871: link becomes ready
[ 30.396644] hassio: port 2(vethc59b871) entered blocking state
[ 30.399988] hassio: port 2(vethc59b871) entered forwarding state
[ 33.820975] hassio: port 3(veth3147c57) entered blocking state
[ 33.822700] hassio: port 3(veth3147c57) entered disabled state
[ 33.824592] device veth3147c57 entered promiscuous mode
[ 33.826094] kauditd_printk_skb: 29 callbacks suppressed
[ 33.826098] audit: type=1700 audit(1567539006.819:77): dev=veth3147c57 prom=256 old_prom=0 auid=4294967295 uid=0 gid=0 ses=4294967295
[ 33.826867] IPv6: ADDRCONF(NETDEV_UP): veth3147c57: link is not ready
[ 33.827506] audit: type=1300 audit(1567539006.819:77): arch=40000028 syscall=290 per=800000 success=yes exit=40 a0=c a1=3c61d10 a2=28 a3=0 items=0 ppid=1 pid=306 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="dockerd" exe="/usr/bin/dockerd" key=(null)
[ 33.838614] audit: type=1327 audit(1567539006.819:77): proctitle=2F7573722F62696E2F646F636B657264002D480066643A2F2F002D2D73746F726167652D6472697665723D6F7665726C617932002D2D6C6F672D6472697665723D6A6F75726E616C64002D2D646174612D726F6F74002F6D6E742F646174612F646F636B6572
[ 33.880568] audit: type=1325 audit(1567539006.879:78): table=nat family=2 entries=13
[ 33.883786] audit: type=1300 audit(1567539006.879:78): arch=40000028 syscall=294 per=800000 success=yes exit=0 a0=4 a1=0 a2=40 a3=194eb80 items=0 ppid=306 pid=870 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="iptables" exe="/usr/sbin/xtables-multi" key=(null)
[ 33.893465] audit: type=1327 audit(1567539006.879:78): proctitle=2F7573722F7362696E2F69707461626C6573002D2D77616974002D74006E6174002D4100444F434B4552002D7000746370002D6400302F30002D2D64706F72740038383834002D6A00444E4154002D2D746F2D64657374696E6174696F6E003137322E33302E33332E303A383838340000002D690068617373696F
[ 33.907568] audit: type=1325 audit(1567539006.899:79): table=filter family=2 entries=29
[ 33.911619] audit: type=1300 audit(1567539006.899:79): arch=40000028 syscall=294 per=800000 success=yes exit=0 a0=4 a1=0 a2=40 a3=55b080 items=0 ppid=306 pid=872 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="iptables" exe="/usr/sbin/xtables-multi" key=(null)
[ 33.918253] audit: type=1327 audit(1567539006.899:79): proctitle=2F7573722F7362696E2F69707461626C6573002D2D77616974002D740066696C746572002D4100444F434B45520000002D690068617373696F002D6F0068617373696F002D7000746370002D64003137322E33302E33332E30002D2D64706F72740038383834002D6A00414343455054
[ 33.925032] audit: type=1325 audit(1567539006.919:80): table=nat family=2 entries=14
[ 35.822881] eth0: renamed from veth3ac344f
[ 35.903834] IPv6: ADDRCONF(NETDEV_CHANGE): veth3147c57: link becomes ready
[ 35.907677] hassio: port 3(veth3147c57) entered blocking state
[ 35.911254] hassio: port 3(veth3147c57) entered forwarding state
[ 42.114334] hassio: port 4(veth8a3edb5) entered blocking state
[ 42.115971] hassio: port 4(veth8a3edb5) entered disabled state
[ 42.117798] device veth8a3edb5 entered promiscuous mode
[ 42.119681] kauditd_printk_skb: 59 callbacks suppressed
[ 42.119686] audit: type=1700 audit(1567539048.730:100): dev=veth8a3edb5 prom=256 old_prom=0 auid=4294967295 uid=0 gid=0 ses=4294967295
[ 42.120182] IPv6: ADDRCONF(NETDEV_UP): veth8a3edb5: link is not ready
[ 42.121203] audit: type=1300 audit(1567539048.730:100): arch=40000028 syscall=290 per=800000 success=yes exit=40 a0=c a1=452c150 a2=28 a3=0 items=0 ppid=1 pid=306 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="dockerd" exe="/usr/bin/dockerd" key=(null)
[ 42.131060] audit: type=1327 audit(1567539048.730:100): proctitle=2F7573722F62696E2F646F636B657264002D480066643A2F2F002D2D73746F726167652D6472697665723D6F7665726C617932002D2D6C6F672D6472697665723D6A6F75726E616C64002D2D646174612D726F6F74002F6D6E742F646174612F646F636B6572
[ 42.245052] audit: type=1325 audit(1567539048.860:101): table=nat family=2 entries=21
[ 42.247872] audit: type=1300 audit(1567539048.860:101): arch=40000028 syscall=294 per=800000 success=yes exit=0 a0=4 a1=0 a2=40 a3=186a80 items=0 ppid=306 pid=1072 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="iptables" exe="/usr/sbin/xtables-multi" key=(null)
[ 42.254022] audit: type=1327 audit(1567539048.860:101): proctitle=2F7573722F7362696E2F69707461626C6573002D2D77616974002D74006E6174002D4100444F434B4552002D7000746370002D6400302F30002D2D64706F72740033353531002D6A00444E4154002D2D746F2D64657374696E6174696F6E003137322E33302E33332E313A333535310000002D690068617373696F
[ 42.274392] audit: type=1325 audit(1567539048.890:102): table=filter family=2 entries=33
[ 42.277860] audit: type=1300 audit(1567539048.890:102): arch=40000028 syscall=294 per=800000 success=yes exit=0 a0=4 a1=0 a2=40 a3=15b780 items=0 ppid=306 pid=1074 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="iptables" exe="/usr/sbin/xtables-multi" key=(null)
[ 42.284675] audit: type=1327 audit(1567539048.890:102): proctitle=2F7573722F7362696E2F69707461626C6573002D2D77616974002D740066696C746572002D4100444F434B45520000002D690068617373696F002D6F0068617373696F002D7000746370002D64003137322E33302E33332E31002D2D64706F72740033353531002D6A00414343455054
[ 42.322041] audit: type=1325 audit(1567539048.940:103): table=nat family=2 entries=22
[ 42.543785] hassio: port 5(veth3aa820b) entered blocking state
[ 42.545400] hassio: port 5(veth3aa820b) entered disabled state
[ 42.547231] device veth3aa820b entered promiscuous mode
[ 42.549425] IPv6: ADDRCONF(NETDEV_UP): veth3aa820b: link is not ready
[ 42.550984] hassio: port 5(veth3aa820b) entered blocking state
[ 42.552537] hassio: port 5(veth3aa820b) entered forwarding state
[ 43.111753] hassio: port 5(veth3aa820b) entered disabled state
[ 45.266008] eth0: renamed from veth22c956b
[ 45.321905] IPv6: ADDRCONF(NETDEV_CHANGE): veth8a3edb5: link becomes ready
[ 45.325425] hassio: port 4(veth8a3edb5) entered blocking state
[ 45.328629] hassio: port 4(veth8a3edb5) entered forwarding state
[ 45.562895] eth0: renamed from vethe3174f6
[ 45.612381] IPv6: ADDRCONF(NETDEV_CHANGE): veth3aa820b: link becomes ready
[ 45.613858] hassio: port 5(veth3aa820b) entered blocking state
[ 45.615251] hassio: port 5(veth3aa820b) entered forwarding state
[ 96.807080] hassio: port 6(veth8484d06) entered blocking state
[ 96.808420] hassio: port 6(veth8484d06) entered disabled state
[ 96.811635] device veth8484d06 entered promiscuous mode
[ 96.812970] kauditd_printk_skb: 74 callbacks suppressed
[ 96.812974] audit: type=1700 audit(1567539103.420:128): dev=veth8484d06 prom=256 old_prom=0 auid=4294967295 uid=0 gid=0 ses=4294967295
[ 96.816522] audit: type=1300 audit(1567539103.420:128): arch=40000028 syscall=290 per=800000 success=yes exit=40 a0=c a1=4333680 a2=28 a3=0 items=0 ppid=1 pid=306 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="dockerd" exe="/usr/bin/dockerd" key=(null)
[ 96.819552] IPv6: ADDRCONF(NETDEV_UP): veth8484d06: link is not ready
[ 96.821473] audit: type=1327 audit(1567539103.420:128): proctitle=2F7573722F62696E2F646F636B657264002D480066643A2F2F002D2D73746F726167652D6472697665723D6F7665726C617932002D2D6C6F672D6472697665723D6A6F75726E616C64002D2D646174612D726F6F74002F6D6E742F646174612F646F636B6572
[ 96.940408] hassio: port 7(veth46bbee1) entered blocking state
[ 96.942408] hassio: port 7(veth46bbee1) entered disabled state
[ 96.944449] device veth46bbee1 entered promiscuous mode
[ 96.945979] audit: type=1700 audit(1567539103.550:129): dev=veth46bbee1 prom=256 old_prom=0 auid=4294967295 uid=0 gid=0 ses=4294967295
[ 96.949356] audit: type=1300 audit(1567539103.550:129): arch=40000028 syscall=290 per=800000 success=yes exit=40 a0=c a1=43338f0 a2=28 a3=0 items=0 ppid=1 pid=306 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="dockerd" exe="/usr/bin/dockerd" key=(null)
[ 96.949829] IPv6: ADDRCONF(NETDEV_UP): veth46bbee1: link is not ready
[ 96.955182] audit: type=1327 audit(1567539103.550:129): proctitle=2F7573722F62696E2F646F636B657264002D480066643A2F2F002D2D73746F726167652D6472697665723D6F7665726C617932002D2D6C6F672D6472697665723D6A6F75726E616C64002D2D646174612D726F6F74002F6D6E742F646174612F646F636B6572
[ 96.962696] hassio: port 7(veth46bbee1) entered blocking state
[ 96.964195] hassio: port 7(veth46bbee1) entered forwarding state
[ 97.001918] audit: type=1325 audit(1567539103.620:130): table=nat family=2 entries=25
[ 97.005243] audit: type=1300 audit(1567539103.620:130): arch=40000028 syscall=294 per=800000 success=yes exit=0 a0=4 a1=0 a2=40 a3=dc7200 items=0 ppid=306 pid=1586 auid=4294967295 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=4294967295 comm="iptables" exe="/usr/sbin/xtables-multi" key=(null)
[ 97.012109] audit: type=1327 audit(1567539103.620:130): proctitle=2F7573722F7362696E2F69707461626C6573002D2D77616974002D74006E6174002D4100444F434B4552002D7000746370002D6400302F30002D2D64706F72740035303530002D6A00444E4154002D2D746F2D64657374696E6174696F6E003137322E33302E33332E333A353035300000002D690068617373696F
[ 97.025733] audit: type=1325 audit(1567539103.640:131): table=filter family=2 entries=35
[ 97.831515] hassio: port 7(veth46bbee1) entered disabled state
[ 100.114619] eth0: renamed from vethe7cd412
[ 100.164808] IPv6: ADDRCONF(NETDEV_CHANGE): veth8484d06: link becomes ready
[ 100.166965] hassio: port 6(veth8484d06) entered blocking state
[ 100.168545] hassio: port 6(veth8484d06) entered forwarding state
[ 100.249546] eth0: renamed from vethcb19faa
[ 100.313185] IPv6: ADDRCONF(NETDEV_CHANGE): veth46bbee1: link becomes ready
[ 100.316793] hassio: port 7(veth46bbee1) entered blocking state
[ 100.320103] hassio: port 7(veth46bbee1) entered forwarding state
[ 331.024112] usb 1-1.1.2: USB disconnect, device number 9
[ 331.341743] usb 1-1.1.2: new full-speed USB device number 10 using dwc_otg
[ 331.476090] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 331.479249] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 331.485453] usb 1-1.1.2: Product: ConBee II
[ 331.488511] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 331.491614] usb 1-1.1.2: SerialNumber: DE1996448
[ 331.496210] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 334.864082] usb 1-1.1.2: USB disconnect, device number 10
[ 335.211721] usb 1-1.1.2: new full-speed USB device number 11 using dwc_otg
[ 335.346215] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 335.349126] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 335.354695] usb 1-1.1.2: Product: ConBee II
[ 335.357387] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 335.360092] usb 1-1.1.2: SerialNumber: DE1996448
[ 335.369410] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 351.550455] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 351.553736] brcmfmac: power management disabled
[ 474.896094] usb 1-1.1.2: USB disconnect, device number 11
[ 475.201840] usb 1-1.1.2: new full-speed USB device number 12 using dwc_otg
[ 475.336209] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 475.338945] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 475.344254] usb 1-1.1.2: Product: ConBee II
[ 475.346926] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 475.349668] usb 1-1.1.2: SerialNumber: DE1996448
[ 475.354894] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 478.736090] usb 1-1.1.2: USB disconnect, device number 12
[ 479.041844] usb 1-1.1.2: new full-speed USB device number 13 using dwc_otg
[ 479.176211] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 479.178964] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 479.184277] usb 1-1.1.2: Product: ConBee II
[ 479.186939] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 479.189668] usb 1-1.1.2: SerialNumber: DE1996448
[ 479.197129] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 498.704156] usb 1-1.1.2: USB disconnect, device number 13
[ 499.011931] usb 1-1.1.2: new full-speed USB device number 14 using dwc_otg
[ 499.146341] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 499.149095] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 499.154416] usb 1-1.1.2: Product: ConBee II
[ 499.157085] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 499.159853] usb 1-1.1.2: SerialNumber: DE1996448
[ 499.169620] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 502.544095] usb 1-1.1.2: USB disconnect, device number 14
[ 502.841921] usb 1-1.1.2: new full-speed USB device number 15 using dwc_otg
[ 502.976594] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 502.979333] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 502.984700] usb 1-1.1.2: Product: ConBee II
[ 502.987399] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 502.990214] usb 1-1.1.2: SerialNumber: DE1996448
[ 502.998475] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 582.416092] usb 1-1.1.2: USB disconnect, device number 15
[ 582.713387] usb 1-1.1.2: new full-speed USB device number 16 using dwc_otg
[ 582.847836] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 582.850560] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 582.855860] usb 1-1.1.2: Product: ConBee II
[ 582.858514] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 582.861265] usb 1-1.1.2: SerialNumber: DE1996448
[ 582.867008] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 586.256129] usb 1-1.1.2: USB disconnect, device number 16
[ 586.603455] usb 1-1.1.2: new full-speed USB device number 17 using dwc_otg
[ 586.737832] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 586.740551] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 586.745878] usb 1-1.1.2: Product: ConBee II
[ 586.748533] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 586.751248] usb 1-1.1.2: SerialNumber: DE1996448
[ 586.760960] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 656.144094] usb 1-1.1.2: USB disconnect, device number 17
[ 656.494486] usb 1-1.1.2: new full-speed USB device number 18 using dwc_otg
[ 656.628843] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 656.631553] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 656.636829] usb 1-1.1.2: Product: ConBee II
[ 656.639473] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 656.642212] usb 1-1.1.2: SerialNumber: DE1996448
[ 656.647451] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 659.984095] usb 1-1.1.2: USB disconnect, device number 18
[ 660.384540] usb 1-1.1.2: new full-speed USB device number 19 using dwc_otg
[ 660.518961] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 660.521684] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 660.526991] usb 1-1.1.2: Product: ConBee II
[ 660.529639] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 660.532351] usb 1-1.1.2: SerialNumber: DE1996448
[ 660.542979] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 667.544311] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 667.546997] brcmfmac: power management disabled
[ 737.040095] usb 1-1.1.2: USB disconnect, device number 19
[ 737.345322] usb 1-1.1.2: new full-speed USB device number 20 using dwc_otg
[ 737.479589] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 737.482328] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 737.487632] usb 1-1.1.2: Product: ConBee II
[ 737.490047] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 737.491261] usb 1-1.1.2: SerialNumber: DE1996448
[ 737.493978] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 740.880093] usb 1-1.1.2: USB disconnect, device number 20
[ 741.195298] usb 1-1.1.2: new full-speed USB device number 21 using dwc_otg
[ 741.329713] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 741.332453] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 741.337813] usb 1-1.1.2: Product: ConBee II
[ 741.340483] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 741.343221] usb 1-1.1.2: SerialNumber: DE1996448
[ 741.351185] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 817.936092] usb 1-1.1.2: USB disconnect, device number 21
[ 818.245824] usb 1-1.1.2: new full-speed USB device number 22 using dwc_otg
[ 818.380215] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 818.382972] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 818.388412] usb 1-1.1.2: Product: ConBee II
[ 818.391196] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 818.394068] usb 1-1.1.2: SerialNumber: DE1996448
[ 818.399105] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 821.776094] usb 1-1.1.2: USB disconnect, device number 22
[ 822.075864] usb 1-1.1.2: new full-speed USB device number 23 using dwc_otg
[ 822.210212] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 822.212964] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 822.218270] usb 1-1.1.2: Product: ConBee II
[ 822.220913] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 822.223632] usb 1-1.1.2: SerialNumber: DE1996448
[ 822.235591] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 845.840098] usb 1-1.1.2: USB disconnect, device number 23
[ 846.135976] usb 1-1.1.2: new full-speed USB device number 24 using dwc_otg
[ 846.270468] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 846.273204] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 846.278510] usb 1-1.1.2: Product: ConBee II
[ 846.281156] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 846.283897] usb 1-1.1.2: SerialNumber: DE1996448
[ 846.295699] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 849.680101] usb 1-1.1.2: USB disconnect, device number 24
[ 849.985996] usb 1-1.1.2: new full-speed USB device number 25 using dwc_otg
[ 850.120349] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 850.123081] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 850.128397] usb 1-1.1.2: Product: ConBee II
[ 850.131038] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 850.133792] usb 1-1.1.2: SerialNumber: DE1996448
[ 850.141576] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 983.554562] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 983.557574] brcmfmac: power management disabled
[ 1114.384098] usb 1-1.1.2: USB disconnect, device number 25
[ 1114.687680] usb 1-1.1.2: new full-speed USB device number 26 using dwc_otg
[ 1114.822087] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 1114.824839] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1114.830160] usb 1-1.1.2: Product: ConBee II
[ 1114.832848] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 1114.835600] usb 1-1.1.2: SerialNumber: DE1996448
[ 1114.845232] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 1118.224092] usb 1-1.1.2: USB disconnect, device number 26
[ 1118.577725] usb 1-1.1.2: new full-speed USB device number 27 using dwc_otg
[ 1118.712088] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 1118.714822] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1118.720119] usb 1-1.1.2: Product: ConBee II
[ 1118.722791] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 1118.725526] usb 1-1.1.2: SerialNumber: DE1996448
[ 1118.729772] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 1299.547232] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1299.550316] brcmfmac: power management disabled
[ 1615.549313] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1615.552526] brcmfmac: power management disabled
[ 1931.553899] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 1931.557484] brcmfmac: power management disabled
[ 2247.554429] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2247.557622] brcmfmac: power management disabled
[ 2274.064097] usb 1-1.1.2: USB disconnect, device number 27
[ 2274.365154] usb 1-1.1.2: new full-speed USB device number 28 using dwc_otg
[ 2274.499593] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2274.502403] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2274.508027] usb 1-1.1.2: Product: ConBee II
[ 2274.510801] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2274.513632] usb 1-1.1.2: SerialNumber: DE1996448
[ 2274.519988] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2277.904097] usb 1-1.1.2: USB disconnect, device number 28
[ 2278.205209] usb 1-1.1.2: new full-speed USB device number 29 using dwc_otg
[ 2278.339591] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2278.342375] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2278.347705] usb 1-1.1.2: Product: ConBee II
[ 2278.350384] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2278.353123] usb 1-1.1.2: SerialNumber: DE1996448
[ 2278.358623] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2296.848126] usb 1-1.1.2: USB disconnect, device number 29
[ 2297.145370] usb 1-1.1.2: new full-speed USB device number 30 using dwc_otg
[ 2297.279840] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2297.282591] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2297.287899] usb 1-1.1.2: Product: ConBee II
[ 2297.290563] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2297.293287] usb 1-1.1.2: SerialNumber: DE1996448
[ 2297.297620] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2300.688099] usb 1-1.1.2: USB disconnect, device number 30
[ 2300.985383] usb 1-1.1.2: new full-speed USB device number 31 using dwc_otg
[ 2301.119843] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2301.122572] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2301.127868] usb 1-1.1.2: Product: ConBee II
[ 2301.130521] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2301.133282] usb 1-1.1.2: SerialNumber: DE1996448
[ 2301.137875] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2382.608104] usb 1-1.1.2: USB disconnect, device number 31
[ 2382.926113] usb 1-1.1.2: new full-speed USB device number 32 using dwc_otg
[ 2383.060468] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2383.063206] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2383.068502] usb 1-1.1.2: Product: ConBee II
[ 2383.071158] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2383.073885] usb 1-1.1.2: SerialNumber: DE1996448
[ 2383.079567] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2386.448128] usb 1-1.1.2: USB disconnect, device number 32
[ 2386.766124] usb 1-1.1.2: new full-speed USB device number 33 using dwc_otg
[ 2386.900588] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2386.903319] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2386.908621] usb 1-1.1.2: Product: ConBee II
[ 2386.911267] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2386.914022] usb 1-1.1.2: SerialNumber: DE1996448
[ 2386.919587] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2456.336097] usb 1-1.1.2: USB disconnect, device number 33
[ 2456.646684] usb 1-1.1.2: new full-speed USB device number 34 using dwc_otg
[ 2456.781091] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2456.783805] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2456.789072] usb 1-1.1.2: Product: ConBee II
[ 2456.791714] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2456.794424] usb 1-1.1.2: SerialNumber: DE1996448
[ 2456.800048] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2460.176095] usb 1-1.1.2: USB disconnect, device number 34
[ 2460.526712] usb 1-1.1.2: new full-speed USB device number 35 using dwc_otg
[ 2460.661093] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2460.663807] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2460.669072] usb 1-1.1.2: Product: ConBee II
[ 2460.671713] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2460.674424] usb 1-1.1.2: SerialNumber: DE1996448
[ 2460.679981] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2537.232129] usb 1-1.1.2: USB disconnect, device number 35
[ 2537.537322] usb 1-1.1.2: new full-speed USB device number 36 using dwc_otg
[ 2537.671718] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2537.674429] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2537.679721] usb 1-1.1.2: Product: ConBee II
[ 2537.682374] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2537.685102] usb 1-1.1.2: SerialNumber: DE1996448
[ 2537.690629] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2541.072100] usb 1-1.1.2: USB disconnect, device number 36
[ 2541.377353] usb 1-1.1.2: new full-speed USB device number 37 using dwc_otg
[ 2541.511718] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2541.514438] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2541.519716] usb 1-1.1.2: Product: ConBee II
[ 2541.522370] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2541.525127] usb 1-1.1.2: SerialNumber: DE1996448
[ 2541.529242] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2563.556171] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2563.559323] brcmfmac: power management disabled
[ 2618.128097] usb 1-1.1.2: USB disconnect, device number 37
[ 2618.437935] usb 1-1.1.2: new full-speed USB device number 38 using dwc_otg
[ 2618.572217] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2618.574950] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2618.580258] usb 1-1.1.2: Product: ConBee II
[ 2618.582933] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2618.585705] usb 1-1.1.2: SerialNumber: DE1996448
[ 2618.595276] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2621.968096] usb 1-1.1.2: USB disconnect, device number 38
[ 2622.277941] usb 1-1.1.2: new full-speed USB device number 39 using dwc_otg
[ 2622.412470] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2622.415217] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2622.420534] usb 1-1.1.2: Product: ConBee II
[ 2622.423218] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2622.425952] usb 1-1.1.2: SerialNumber: DE1996448
[ 2622.434387] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2646.032105] usb 1-1.1.2: USB disconnect, device number 39
[ 2646.338078] usb 1-1.1.2: new full-speed USB device number 40 using dwc_otg
[ 2646.472469] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2646.475204] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2646.480512] usb 1-1.1.2: Product: ConBee II
[ 2646.483174] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2646.485932] usb 1-1.1.2: SerialNumber: DE1996448
[ 2646.495819] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2649.872100] usb 1-1.1.2: USB disconnect, device number 40
[ 2650.168200] usb 1-1.1.2: new full-speed USB device number 41 using dwc_otg
[ 2650.302626] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 2650.305355] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2650.310643] usb 1-1.1.2: Product: ConBee II
[ 2650.313365] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 2650.316080] usb 1-1.1.2: SerialNumber: DE1996448
[ 2650.321500] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 2879.557961] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2879.561006] brcmfmac: power management disabled
[ 3195.559991] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3195.562219] brcmfmac: power management disabled
[ 3511.561704] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3511.564884] brcmfmac: power management disabled
[ 3611.920100] usb 1-1.1.2: USB disconnect, device number 41
[ 3612.223873] usb 1-1.1.2: new full-speed USB device number 42 using dwc_otg
[ 3612.358347] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 3612.361116] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3612.366492] usb 1-1.1.2: Product: ConBee II
[ 3612.369157] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 3612.371923] usb 1-1.1.2: SerialNumber: DE1996448
[ 3612.376660] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 3615.760102] usb 1-1.1.2: USB disconnect, device number 42
[ 3616.073992] usb 1-1.1.2: new full-speed USB device number 43 using dwc_otg
[ 3616.208355] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 3616.211131] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3616.216521] usb 1-1.1.2: Product: ConBee II
[ 3616.219193] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 3616.221965] usb 1-1.1.2: SerialNumber: DE1996448
[ 3616.230354] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 3827.563795] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3827.566892] brcmfmac: power management disabled
[ 4074.512102] usb 1-1.1.2: USB disconnect, device number 43
[ 4074.816474] usb 1-1.1.2: new full-speed USB device number 44 using dwc_otg
[ 4074.950851] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4074.953616] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4074.958938] usb 1-1.1.2: Product: ConBee II
[ 4074.961601] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4074.964349] usb 1-1.1.2: SerialNumber: DE1996448
[ 4074.975438] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4078.352102] usb 1-1.1.2: USB disconnect, device number 44
[ 4078.656484] usb 1-1.1.2: new full-speed USB device number 45 using dwc_otg
[ 4078.790849] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4078.793598] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4078.798948] usb 1-1.1.2: Product: ConBee II
[ 4078.801643] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4078.804396] usb 1-1.1.2: SerialNumber: DE1996448
[ 4078.814578] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4097.296106] usb 1-1.1.2: USB disconnect, device number 45
[ 4097.596563] usb 1-1.1.2: new full-speed USB device number 46 using dwc_otg
[ 4097.730974] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4097.733724] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4097.739025] usb 1-1.1.2: Product: ConBee II
[ 4097.741671] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4097.744462] usb 1-1.1.2: SerialNumber: DE1996448
[ 4097.750157] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4101.136103] usb 1-1.1.2: USB disconnect, device number 46
[ 4101.436648] usb 1-1.1.2: new full-speed USB device number 47 using dwc_otg
[ 4101.570975] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4101.573696] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4101.578971] usb 1-1.1.2: Product: ConBee II
[ 4101.581610] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4101.584341] usb 1-1.1.2: SerialNumber: DE1996448
[ 4101.589298] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4143.570214] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4143.571535] brcmfmac: power management disabled
[ 4183.056103] usb 1-1.1.2: USB disconnect, device number 47
[ 4183.357842] usb 1-1.1.2: new full-speed USB device number 48 using dwc_otg
[ 4183.492219] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4183.494967] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4183.500260] usb 1-1.1.2: Product: ConBee II
[ 4183.502952] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4183.505716] usb 1-1.1.2: SerialNumber: DE1996448
[ 4183.515709] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4186.896108] usb 1-1.1.2: USB disconnect, device number 48
[ 4187.197891] usb 1-1.1.2: new full-speed USB device number 49 using dwc_otg
[ 4187.332347] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4187.335078] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4187.340367] usb 1-1.1.2: Product: ConBee II
[ 4187.343026] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4187.345776] usb 1-1.1.2: SerialNumber: DE1996448
[ 4187.352206] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4207.888163] usb 1-1.1.2: USB disconnect, device number 49
[ 4208.198192] usb 1-1.1.2: new full-speed USB device number 50 using dwc_otg
[ 4208.332598] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4208.335328] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4208.340622] usb 1-1.1.2: Product: ConBee II
[ 4208.343295] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4208.345573] usb 1-1.1.2: SerialNumber: DE1996448
[ 4208.349523] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4211.728102] usb 1-1.1.2: USB disconnect, device number 50
[ 4212.038303] usb 1-1.1.2: new full-speed USB device number 51 using dwc_otg
[ 4212.172597] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4212.175317] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4212.180573] usb 1-1.1.2: Product: ConBee II
[ 4212.183215] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4212.185927] usb 1-1.1.2: SerialNumber: DE1996448
[ 4212.197847] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4256.784104] usb 1-1.1.2: USB disconnect, device number 51
[ 4257.098841] usb 1-1.1.2: new full-speed USB device number 52 using dwc_otg
[ 4257.233981] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4257.236708] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4257.242061] usb 1-1.1.2: Product: ConBee II
[ 4257.244709] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4257.247420] usb 1-1.1.2: SerialNumber: DE1996448
[ 4257.253236] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4260.624103] usb 1-1.1.2: USB disconnect, device number 52
[ 4260.938903] usb 1-1.1.2: new full-speed USB device number 53 using dwc_otg
[ 4261.073347] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4261.076053] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4261.081339] usb 1-1.1.2: Product: ConBee II
[ 4261.083977] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4261.086695] usb 1-1.1.2: SerialNumber: DE1996448
[ 4261.096871] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4307.728105] usb 1-1.1.2: USB disconnect, device number 53
[ 4308.029568] usb 1-1.1.2: new full-speed USB device number 54 using dwc_otg
[ 4308.163975] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4308.166706] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4308.172012] usb 1-1.1.2: Product: ConBee II
[ 4308.174664] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4308.177380] usb 1-1.1.2: SerialNumber: DE1996448
[ 4308.185751] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4311.568103] usb 1-1.1.2: USB disconnect, device number 54
[ 4311.869566] usb 1-1.1.2: new full-speed USB device number 55 using dwc_otg
[ 4312.005599] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4312.008326] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4312.013647] usb 1-1.1.2: Product: ConBee II
[ 4312.016300] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4312.019022] usb 1-1.1.2: SerialNumber: DE1996448
[ 4312.023340] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4336.656104] usb 1-1.1.2: USB disconnect, device number 55
[ 4336.969884] usb 1-1.1.2: new full-speed USB device number 56 using dwc_otg
[ 4337.114600] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4337.117335] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4337.122667] usb 1-1.1.2: Product: ConBee II
[ 4337.125348] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4337.128124] usb 1-1.1.2: SerialNumber: DE1996448
[ 4337.138097] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4340.496103] usb 1-1.1.2: USB disconnect, device number 56
[ 4340.799909] usb 1-1.1.2: new full-speed USB device number 57 using dwc_otg
[ 4340.934348] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4340.937061] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4340.942355] usb 1-1.1.2: Product: ConBee II
[ 4340.945004] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4340.947750] usb 1-1.1.2: SerialNumber: DE1996448
[ 4340.954246] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4418.576104] usb 1-1.1.2: USB disconnect, device number 57
[ 4418.890822] usb 1-1.1.2: new full-speed USB device number 58 using dwc_otg
[ 4419.035849] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4419.038577] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4419.043876] usb 1-1.1.2: Product: ConBee II
[ 4419.046536] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4419.049308] usb 1-1.1.2: SerialNumber: DE1996448
[ 4419.053380] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4422.416261] usb 1-1.1.2: USB disconnect, device number 58
[ 4422.720878] usb 1-1.1.2: new full-speed USB device number 59 using dwc_otg
[ 4422.855348] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4422.858071] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4422.863353] usb 1-1.1.2: Product: ConBee II
[ 4422.866003] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4422.868753] usb 1-1.1.2: SerialNumber: DE1996448
[ 4422.875493] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4445.456103] usb 1-1.1.2: USB disconnect, device number 59
[ 4445.761138] usb 1-1.1.2: new full-speed USB device number 60 using dwc_otg
[ 4445.895474] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4445.898187] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4445.903464] usb 1-1.1.2: Product: ConBee II
[ 4445.906109] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4445.908857] usb 1-1.1.2: SerialNumber: DE1996448
[ 4445.914598] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4449.296104] usb 1-1.1.2: USB disconnect, device number 60
[ 4449.611182] usb 1-1.1.2: new full-speed USB device number 61 using dwc_otg
[ 4449.745603] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 4449.748310] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4449.753639] usb 1-1.1.2: Product: ConBee II
[ 4449.756333] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 4449.759155] usb 1-1.1.2: SerialNumber: DE1996448
[ 4449.769688] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device
[ 4459.580459] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4459.583461] brcmfmac: power management disabled
[ 4775.574053] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 4775.577133] brcmfmac: power management disabled
//Mattias

Från: Pascal Vizeli [e-mail]
Svara till: home-assistant/hassio-addons [e-mail]
Datum: tisdag 3 september 2019 22:52
Till: home-assistant/hassio-addons [e-mail]
Kopia: Mattias Hemborg [e-mail], Comment [e-mail]
Ämne: Re: [home-assistant/hassio-addons] deCONZ - FATAL: No device since 3.4 / 3.5 (#685)

what say the dmesg after start?

—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub, or mute the thread.

[KennethLavrsen]

I think the original reporter did not restart HA but only the addon when he reported that it does not work with any device. I can make it work with /dev/ttyACM1.
We may want the original reporter to verify that it works for him if he restarts the entire HA installation.

I also notice that @mattias1972 refers to an error "Config entry for deconzm not ready yet. Retrying in 5 seconds." That is not the error I get and that the original report says. I think that is another problem. It could be the old ModemManager that spooks again. Mattias. Have you disabled modem manager (https://community.home-assistant.io/t/zwave-and-modemmanager/128417/3)

What is broken is using the /dev/serial/by-id/usb-dresden_elektronik_ingenieurtechnik_GmbH_ConBee_II_.......

The error message is that it cannot find this device. It worked fine until I upgraded to the 3.5 (from 3.3).

In the bare metal host the by-id link is present still.

[pvizeli]

The question is, what is different on your baremetal setup. Tested with docker 18.09 and 19.03 / supervisor 185 -> HassOS, Debian, Ubuntu 18.04 (Desktop)

[pvizeli]

@mattias1972 docker is not plug&play. If you plug out the stick at back again, you need restart the add-on, but the device is block by docker and it create every time a new ttyUSBx. Try a full host reboot to become a clean state

[mattias1972]

@mattias1972 docker is not plug&play. If you plug out the stick at back again, you need restart the add-on, but the device is block by docker and it create every time a new ttyUSBx. Try a full host reboot to become a clean state

It still refuses to start despite a reboot of the Pi. dmesg shows fewer entrys about the combee but still there are 10 of them this beeing the last one:
77.051689] usb 1-1.1.2: USB disconnect, device number 10
[ 77.401865] usb 1-1.1.2: new full-speed USB device number 11 using dwc_otg
[ 77.536208] usb 1-1.1.2: New USB device found, idVendor=1cf1, idProduct=0030
[ 77.537386] usb 1-1.1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 77.539587] usb 1-1.1.2: Product: ConBee II
[ 77.540730] usb 1-1.1.2: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 77.542019] usb 1-1.1.2: SerialNumber: DE1996448
[ 77.545521] cdc_acm 1-1.1.2:1.0: ttyACM0: USB ACM device

[KennethLavrsen]

I have triple checked again and I have this config

{
  "device": "/dev/serial/by-id/usb-dresden_elektronik_ingenieurtechnik_GmbH_ConBee_II_DE1962724-if00",

and I get the error

starting version 237

[23:21:48] FATAL: No device /dev/serial/by-id/usb-dresden_elektronik_ingenieurtechnik_GmbH_ConBee_II_DE1962724-if00 found!

And extra check that I use the correct device

root@homeassistant:/dev/serial/by-id# ls -al
total 0
drwxr-xr-x 2 root root 80 Sep  3 23:31 .
drwxr-xr-x 4 root root 80 Sep  3 22:48 ..
lrwxrwxrwx 1 root root 13 Sep  3 23:17 usb-0658_0200-if00 -> ../../ttyACM0
lrwxrwxrwx 1 root root 13 Sep  3 23:31 usb-dresden_elektronik_ingenieurtechnik_GmbH_ConBee_II_DE1962724-if00 -> ../../ttyACM1

[mkarnebeek]

Same here. Broke when updating from 3.3 to 3.5 with the same stick. Using /dev/serial/by-id/usb-dresden_elektronik_ingenieurtechnik_GmbH_ConBee_II_DE1995908-if00 which is there, even within the container.

[pvizeli]

Tested with docker 18.09 and 19.03

Since no one gives details about his installation, I would suggest that you have the wrong docker installed and not docker-ce.

[mkarnebeek]

This is hassio, latest everything, except for home assistant itself (0.97.2), and deconz addon (3.3). Let me know where in hassio you'd like to have a dump for more formation about internals (docker, etc.)

As far as I can see from the UI, i've gathered the following info:

• hassio supervisor 185
• via Portainer, I've discovered i'm running Docker Standalone 18.09.4

[pvizeli]

docker-ce? BaseOS?

[pvizeli]

I had setup now a new ubuntu core 18.04. Install all dependencies and docker-ce (From docker repository). Everythings work with "/dev/serial/by-id/usb-FTDI_FT230X_Basic_UART_DM01H1ID-if00-port0"

I can't help here. I think there is an issue on setup. There was an update on how the supervisor spinup itself from 5 months. Maybe you run the old service files. Execute:
curl -sL https://raw.githubusercontent.com/home-assistant/hassio-installer/master/hassio_install.sh | sudo bash -s

to update the installation and restart the server. That could help

[KennethLavrsen]

I think we have several populations here.

1. From #680 people that already had the issue before the 3.4/3.5 update
2. People that get an error that device is not ready yet
3. And then we are at least 3 or 4 that have the situation where the by-id link does not work in 3.5 but works in 3.3

They should probably be split on 3 bug reports

I am only addressing case 3 which is what seems to best fit the original report.

I surely run docker-ce. I had upgraded to the latest 0.98.2 before the upgrade of deconz and it worked. I know because when it fails all my automatic light stops working so I would have noticed

Mine broke down the minute I upgraded the deconz addon from 3.3 to 3.5 (did not see the 3.4 update) and to get it back I had to use the straight /dev/ttyACM# link

When I look at the host Ubuntu I notice that udev create symbolic links from /dev/serial/by-id that point back to /dev
When I use the ssh within HA the docker view of things are that /dev/serial/by-id/device_name are "files" and not links. I do not know if this means anything but it is an observation

I also have an Aeotec Z-wave stick using ZHA.

It is configured and WORKS like this

zwave:
  usb_path: /dev/serial/by-id/usb-0658_0200-if00
  network_key: !secret zwave_network_key

So for the zwave integration the by-id works fine.

In the Home Assistant hass.io -> Host System -> Hardware button I can the the two by-id devices

The error message from deconz is "FATAL: No device /dev/serial/by-id/usb-dresden_elektronik_ingenieurtechnik_GmbH_ConBee_II_DE1962724-if00 found!"

This is the same error you get if you put some complete nonsense.

The conclusion I have so far that this seems to be an isolated problem to the deconz docker container. Inside this the by-id devices do not exist. We need to find out why. If we go back a few versions of deconz it did not work either. Then the feature was introduced so you could use by-id links. And now it is broken again. And it happens in a release where udev was dramatically chanced as far as I can see in the code without understanding what is it that happens. It seems some udev related stuff was change to using a python based library. But I do not know Python so I am a bit lost

[KennethLavrsen]

You say everything works with Everythings work with "/dev/serial/by-id/usb-FTDI_FT230X_Basic_UART_DM01H1ID-if00-port0"

That does not look like a deconz device. At least all I have seen are not named like that. A deconz device name normally has dresden_elektronik_ingenieurtechnik_GmbH in them. So are you testing in a deconz container?

[KennethLavrsen]

Just came home from work so I could access the HA machine from command line.

I tried the script https://raw.githubusercontent.com/home-assistant/hassio-installer/master/hassio_install.sh and restarted server - it made no difference

I then tried to restore a snapshot of HA but I kept all current and only restored deconz 3.1. I did not have a snap with 3.3 sorry. But when I restore deconz 3.1 it works again with the 'by-id' device. And when I upgrade deconz back to latest it breaks again. It cannot be a setup or docker version issue. And it is not related to the changes in hass.io done recently. It is isolated to deconz. 3.1 works. 3.5 fails to use by-id links. I have to use simple /dev/tty devices again to make it work.

[mattias1972]

Five reboots later deCONZ addon suddenly has decided to work again. I have no idea what was wrong and no clue why it works again... Maybe my Conbee II is faulty, only time will tell, for the moment everything work again.

[pvizeli]

@KennethLavrsen I have all devices from deCONZ. The ID above was a Conbe1.

I'm wrong, after rerunning the installation, you need to destroy the supervisor container to start a rebuild with new parameters. docker rm hassio_supervisor.

I close the issue after I tested it on a HassOS, Debian, Ubuntu with a fresh installation and with latest installer scripts. There is no Python, because it's a complex system between Linux kernel, udev bus, and docker as it is. This work only with "latest" spinup of supervisor. If you run the supervisor container with an older setup before 5 month, there is an issue with trigger reload of udev devices overall containers they are listening to the linux kernel bus. I add detection for this setup and let print an error in next supervisor version.

[KennethLavrsen]

@balloob I want to complain about how this issue is treated. We are several people with the same issue and there is no resolution.

I will reopen new issue with same content

[KennethLavrsen]

And for the record
I have done all suggestions so far and I just did the docker rm hassio_supervisor
And I reran the install script.

And it still fails the same way.

It is not correct to close an issue after so short time when several people are reporting the same issue. I can understand if it is one socker that refuse to try anything. But we are multiple people with same issue and there is obvious an issue caused by the changes in deconz 3.5

I will also say that mattias1972 reported a completely different symptom and his resolution has nothing to do with the issue originally reported.

The least one can do is revert the changes back to what actually worked until we understand what goes wrong.

[KennethLavrsen]

I continue gathering info.

I read up on docker and now I know how to create a bash session on a running container.

And to my surprise I can find /dev/serial/by-id/usb-... links to both sticks and they are symlinks and they point to the right place.

So I tried again to change the deconz config to the by-id device and restarted deconz only. And it worked. Why? What? So I tried to see if this was a lasting fixed by itself situation. No it is not! After a restart of HA I am back to not working with same error message. The container was then manually started and it worked. And then tried many boots of the entire metal machine as well as HA. It works every 3rd time or so.

It seems to be a timing issue. Maybe udev is not done running before deconz is started and trying to access the device. It is a "no device found" error. Not access denied or device busy or similar. So my best guess now is that either udev does not always succeed creating the by-id symlinks or it does it too late. I need advice how to debug this further.

@pvizeli will you be so kind and reopen this so we do not discuss this on a github issue that soon freezes for comments?

[KennethLavrsen]

I am trying to figure out what is going on at start. But I do not understand how the docker thing works. I am a docker noob obviously.

I can see in my /usr/share/hassio/addons/core/deconz/data directory that there is a run.sh that seems to be a bash script that start up deconz. But it is obviously not this script that runs because when I edit the file no change is done. There is a 3 second delay I would like to increase to 5 or 10 to see if it makes a difference. How do I get this change made effective?

[KennethLavrsen]

I have been working half the night yesterday, reading HA dev documentation at work, and worked several hours today trying to debug this. I am stuck at how to modify the run.sh script and rebuild the deconz image with the change. I have asked on Discord in the dev_general channel but noone has been there today that could help.

I really tried to understand the addon development documentation and I tried many things that all failed.

I need help to pass the point where I am stuck. I really want to participate and spend the hours debugging and root causeing this and I respect that it is impossible for @pvizeli to fix something he cannot reproduce. But I can reproduce it here. If I restart deconz 10 times it fails 50% of the time. It can work 5 times in a row and fail 5 times in a row. But it is 50/50 that it fails or start normally with by-id device. I have a theory that the delay of 3 seconds may not be enough in some cases. It can also be that udev fails to create the symlink. To find out what it is I need to be able to alter and add debug echos to the run.sh script

I just cannot find out how to get the docker container rebuilt with my changes. I do not understand how it works. I need help. A one liner - this is how to rebuild the container picking up the altered run.sh is what I need. Please

[KennethLavrsen]

I gave up on using the Home Assistant Addon version of deconz.

I found that it was dead easy to install deconz from the original Debian repository. Then it updates every time I do apt upgrade. Much easier. And it runs on bare metal. No docker shit. So no more worries about devices swapping around. So if someone else want to escalate this issue then go ahead. I am done. I also moved mqtt and other things back to bare metal some time ago.

[mkarnebeek]

I've just locked this addon on 3.3 and will not be updating it anymore. My vacation starts tomorrow, so i'll be out for a while. Hopefully this will eventually get fixed.

[KennethLavrsen]

Another with same issue

https://community.home-assistant.io/t/deconz-official-thread/100504/577

Sad that the developer refuses to fix it and assume we are all wrong

[frenck]

I think your last comment (the last line) is completely unnecessary, disrespectful and not called for @KennethLavrsen.

Sorry to hear you are having issues, but without a reproduction scenario, it will be hard for anyone to fix (as you've said yourself earlier). Both me and Pascal have a large number of (different) test systems. On none of those, it is reproducible.

This has nothing to do with refusing to fix it.

[KennethLavrsen]

@frenck

I think closing an issue claiming there is no issue is equally disrespectful to all the people with the problem. And then repeating it again to a new user closing exactly same issue one more time.

And I am sorry for only being a human with human feelings. I got upset. In the official deconz forum topic there are new people that reported the same issue. It affects many people.

I spent more than 20 hours trying to debug the problem but I got stuck because I still do not understand how to rebuild a docker after changing the script that runs when it starts. I tried to get help in the dev channels on discord but noone was present to help me.

I can see that there is a 3 second delay in the script and my current theory is that the new way of running udev takes more than the 3 seconds on some computers depending on how much hardware that needs to be discovered.

I tried to read the dev docs carefully but I know too little about dockers to understand how to rebuild the containers with changed content. I tried many things but always end up with the original code running with the 3 second delay

I fixed MY immediate issue by moving to a non Home Assistant solution (bare metal). I am trying to help the other users that try to use the HA addon now.

The way forward that I suggest is

• Reopen this bug
• Try and build the addon changing the 3 second delay to a wait for the serial device to be existing - with a timeout of maybe 30 or 60 seconds so the addon can die if the device was defined wrong by the user
• Release this as an update even if you cannot confirm it fixes the issue and ask the people that reported the issue to come back with feedback if it fixes it.